- 1 How do I reset my Sony MHC?
- 2 How do I reset my Sony receiver?
- 3 How do I reset my Sony MHC GX450?
- 4 How do I reset my Sony CD player?
- 5 How do you reset your music system?
- 6 Where is the reset button on a Sony receiver?
- 7 How do I reset my Sony home theater?
- 8 How do I reset my Sony car stereo without the reset button?
- 9 How do I fix Mecha error?
- 10 How do I reset my Sony DVD player without a remote?
- 11 Why do CD players stop working?
- 12 How do I reset my CD player?
- 13 How do you fix a disc that won’t read?
How do I reset my Sony MHC?
Use the buttons on the system to perform this operation.
- Unplug the AC power cord (mains lead) from the system, then plug it back in.
- Press (power) to turn on the system.
- Hold down GUITAR and MEGA BASS for about 3 seconds. [RESET] appears on the display. After the reset completes, the system automatically reboots.
How do I reset my Sony receiver?
Initialize or Reset My Audio/Video (A/V) Receiver to Factory Default Settings
- Press the POWER button to power off the receiver.
- Press and hold down the POWER button.
- Wait approximately 5 seconds and then release the POWER button.
How do I reset my Sony MHC GX450?
Related Sony MHC-GX450 Manual Pages
- Disconnect the power cord.
- Reconnect the power cord.
- Press x, PLAY MODE/TUNING MODE and DISC 1 at the same time.
- Press?/1 to turn down the volume of an audio reproducer, make sure you connect the transmitter to the factory settings.
How do I reset my Sony CD player?
Sony CD players have a Reset button located on the front of the device.
- Turn the player on, whether by plugging it into a power outlet, or simply running it on battery power.
- Press the “Reset” button using a small, pointed object, such as the pointed end of a pencil or pen.
How do you reset your music system?
Unplug the Component The easiest way to reset an audio component is to disconnect it from the power source, wait 30 seconds, and then plug it back in and try again.
How to reset the Audio/Video (A/V) receiver.
- Press the POWER button to turn off the A/V receiver.
- Press and hold down the MUTING and MUSIC buttons.
- While holding down the MUTING and MUSIC buttons, press and release the POWER button to turn the A/V receiver on.
How do I reset my Sony home theater?
Follow this procedure to reset the DVD home theatre system to the factory default specifications.
- While the DVD player is in the stop mode, press the DVD SETUP button.
- Press the UP ARROW or DOWN ARROW to select SETUP.
- Press the ENTER button.
- Press the UP ARROW or DOWN ARROW to select RESET.
- Press the ENTER button.
Devices without a reset button
- Depending on your car stereo, press DSPL and (back) /MODE, DSLP and CALL button, or SOURCE/OFF button for more than two seconds.
- Turn on your car stereo.
How do I fix Mecha error?
Follow the steps below to troubleshoot if the unit not responding properly or displays MECHA ERROR or MECHANICAL ERROR.
- Remove any CDs or tapes from the unit.
- Turn off the unit.
- Unplug the AC power cord for 15 seconds.
- Ensure the recommended speakers are attached properly and that the wires are not shorted.
How do I reset my Sony DVD player without a remote?
How do I reset my Sony Blu Ray player without a remote?
- Turn off and unplug the Blue-Ray player, let it rest for 30 seconds.
- Press and hold the open/close button on the front of the player, reconnect the power cord, then release the button.
Why do CD players stop working?
A scratched or damaged disc is often the culprit and not the player. Use a newer disc if possible to ensure the condition is pristine. If the problem persists with the new disc, remove all discs and run a power cycle to reset the player. Remove any batteries or unplug it to drain the power.
How do I reset my CD player?
How to reset the CD player.
- Unplug the power cord of the CD player from the AC wall outlet.
- Allow the CD player to set without power for 30 seconds.
- Plug the power cord of the CD player back into the AC wall outlet.
How do you fix a disc that won’t read?
5 Ways to Repair a CD or DVD
- Clean the disc using a soft lint-free cloth and a dab of warm water and mild detergent.
- Fill scratches with toothpaste.
- Soften scratches with heat from a 60W lightbulb.
- Fill the scratch with a wax-based product.
- Cover holes in the data layer with pen and tape.